1、濟南專業防水http://www.7788qn.com/談到防水涂料應該選擇品牌新型聚合物水泥基防水涂料。因?yàn)檫@類材料是專門針對家庭防水特點而研制開發的，材料由有機高分子液料和無機粉料復合而成，融合了有機材料彈性高和無機材料耐久性好的優點，涂覆后形成高強堅韌的防水涂膜，具有防水性能好、耐老化，抗龜裂等優勢，綠色環保，施工方便等特點。
Jinan professional waterproof waterproof coating should choose the brand comes to the new polymer cement-based waterproof coating. Because these materials are designed for family and developed a waterproof characteristics, composite materials made from organic materials and inorganic polymer powder was made, the integration of organic materials and inorganic materials, durability, high flexibility, good benefits, after the formation of high-strength coating tough waterproof coating, with good water resistance, anti-aging, anti-cracking and other advantages of convenience, environmental protection, construction and other features.
2、濟南專業防水介紹基面處理是防水施工關鍵，防水材料涂刷基面要求堅固、干凈。基面必須堅固、平整、干凈，無灰塵、油膩、蠟、脫模劑等以及其它碎屑物質；基面有孔隙、裂縫、不平等缺陷的，須預先用水泥砂漿修補抹平，伸縮縫建議粘貼塑膠條，節點須加一層無紡布，管口填充建議使用雷邦仕管口灌漿料。
Jinan professional waterproof introduce base surface treatment is the key to waterproof construction, waterproof material brushing sturdy base surface clean. Base must be strong, smooth, clean and free of dust, grease, wax, release
agents and other detritus; base has pores, cracks, inequality defects shall be pre-patched with cement mortar smooth, joints proposal paste the plastic strip, the node must add a layer non-woven, filling spout nozzle is recommended Lei
Bangshi grout.
3、濟南專業防水http://www.7788qn.com/介紹涂刷防水涂料每層厚度不能超過1mm，兩層涂刷總厚度不能超過2mm。涂刷時力度均勻，注意不要漏刷；前后兩遍涂刷時保持垂直相交的角度，以充分覆蓋到位；單次涂刷不宜過厚，特別是管口和轉角處。
Jinan professional waterproof introduce brushing waterproof coating thickness of each layer should not exceed 1mm, the total thickness of no more than two brushing 2mm. When brushing uniform intensity, be careful not to leak brush;
perpendicular angle to keep brushing twice before, in order to fully cover in place; a single brush should not be too thick, especially the nozzle and corner.
